原文:污水处理中螺杆泵的选型和使用技巧:螺杆泵因其有可变量运送、自吸能力强、可逆转、能运送含固体颗粒的液体等特点,在污水处理厂中,广泛地被使用在运送水、排污泵湿污泥和絮凝剂药液方面。螺杆泵选用应遵循经济、合理、靠得住的原则。如果在设计选型方面考虑不周,会给以后的使用、管理、维修带来麻烦,所以选用一台按生产实际需要,合理靠得住的螺杆泵既能保证生产顺利进行,又可降低修理成本。1、选择螺杆泵的转速:螺杆泵的流量与转速成线性关系,相对多级泵低转速的螺杆泵,高转速的螺杆泵虽能增长了流量和扬程,但功率明显增大,高转速加速了转子与定子间的磨耗,必定使螺杆泵过早无效,而且高转速螺杆泵的定转子长度很短,极易磨耗,因而缩短了螺杆泵的使用寿命。通过减速机构或无级调速机构来降低转速,使其转速保持在每分三百转以下较为合理的范围内,与高速运转的螺杆泵相比,使用寿命能延长几倍。2、考虑螺杆泵的品质:现在市场上的螺杆泵的品类较多,相对而言,进口中开泵的螺杆泵设计合理,材质精良,但价格较高,服务方面有的不到位,配件价格高,订货周期长,可能影响生产的正常运行。国内生产的大都仿造进口产物,产物质量良莠不齐,在选用国内生产的产物时,在考虑其性价比的时候,选用低转速,长导程,传动量部件材质优良,额定寿命长的产物。三、确保杂物不进入泵体:湿污泥中混入的固体杂物会对管道泵螺杆泵的橡胶材质定子造成损坏,所以确保杂物不进入泵的腔体是很重要的,很多污水厂在泵前加装了粉碎机,也有的安装格栅装配或滤网,阻挡杂物进入螺杆泵,对格栅应及时清捞以免造成拥塞。四、避免断料:螺杆泵决不允许在断料的景象下运转,一经消防泵发生,橡胶定子因为干摩擦,瞬间产生高温而烧坏,所以,粉碎机完好,格栅流通是螺杆泵正常运转的必要条件之一,为此,有些螺杆泵还在泵身上安装了断料停机装配,当发生断料时,因为螺杆泵其有自吸功能的特征,腔体内会产生真空,真空装配会使螺杆泵遏制运转。五、保持恒定的出口压力:螺杆泵是一种容积式回转泵,当出口端受阻以后,压力会逐渐升高,以至于超过预定的压力值。此时电机负荷急剧增长。传动机械相关零件的负载也会超出设计值,严重特殊情况发生电机废弃、传动零件断裂。为了避免螺杆泵损坏,一般会在螺杆泵出口处安装旁通溢流阀,用以稳定出口压力,保持泵的正常运转。

"Treatment selection and use of screw tips"是由中国离心泵网供给的水泵行业新闻,译文仅供参考。别的,中国离心泵网还供给相关产物搜索:离心泵型号、离心泵价格、离心泵技术、离心泵新闻、离心泵生产商等。

译文:Wastewater Treatment Selection and use of screw tips:Screw because there can be variable transmission,self-priming capability,and can be reversed to transport the liquid containing solid particles,etc.,in wastewater treatment plant,widely used in the transportation of water,wet sludge and liquid flocculant side.Screw pump used should follow the economic,rational and reliable principle.If the selection of areas in the design of ill-considered,would later use,management,maintenance,trouble,so choose one according to the actual needs Screw pumpsof production,reasonable and reliable screw pump can guarantee the smooth progress of production,but also reduce the repair costs.A selected screw speed:Screw pump flow and speed into alinear relationship between the screw relative to the low speed and high speed screw pump could increase the flow and head,but significantly increased power,high-speed accelerated between the rotor and the stator wear,premature failure will make screw pump,an dhigh speed screw pump rotor length is very short,easy Suber-water pumpsto wear,and thus shorten the life of the screw pump.Through the reduction gear to reduce speed or stepless speed regulation body,to speed to keep the following in each sub-300 switch to amore reasonable range,and high-speed operation of the screw than life can be extended several times.Second,considering the quality of screw pump:Now the type of screw pump on the market more,relatively speaking,the screw pump designed imported,material well,but the price is high,services,and some are not in place,fitting high price,order cycle length,may affect the production normal operation.Most of the domestic production of imported generic products,product quality Self-priming pumpsvaries greatly,in the selection of domestically produced product,when considering its cost,use low speed,long-lead,high transmission capacity component material,rated long life products.Third,to ensure that debris does not enter the pump:Wet sl udge mixed with the solid debris will screw the rubber material damage to the stator,so to ensure that Magnetic pumpsdebris does not enter the pump chamber is very important,many wastewater treatment plant before the installation of agrinder in the pump,and some install grid device or filter,blocking debris into the pump,the grid should be clear winners in time to avoid congestion.Fourth,to avoid breaking material:Screw must not be allowed in the case of blanking operation,upon occurrence of the stator as dry friction of rubber,produces instant heat and burn,so good grinder,screw grille flow is anecessary condition for normal operation To this end,some screw pump body is also expected to stop off device installed,when there Fracture,because he has aself-priming screw pump function of the characteristicsChemical pumps of the body will produce avacuum chamber,vacuum screw pump will stop operation.Fifth,maintain aconstant outlet pressure:Screw pump is apositive displacement rotary pumps,when the exit delay after the pressure will gradually increase,so that the pressure exceeds apredetermined value.At this point asharp increase in motor load.Transmission machinery-related parts of the load will exceed the design value,and in severe electrical burn occurs,transmission parts break.To avoid damage to screw pump,usually installed in the screw pump bypass relief valve outlet,the outlet pressure to stabilize and maintain the normal operation of the pump.

原文来源:"七"乐无穷,尽在新浪新版博客,快来体验啊~请点击进入~